Bullet Softbody Patch
Soft body patches are two-dimensional rectangular meshes, which can be used to simulate for example a flag, a tapestry, or sheets of paper.
Setting up a soft body patch is similar to soft body ropes, but a few extra settings have to be done. The following code will create rectangular path with 31 by 31 segments, and thus 32 x 32 nodes.
from panda3d.bullet import BulletSoftBodyNode info = self.world.getWorldInfo() info.setAirDensity(1.2) info.setWaterDensity(0) info.setWaterOffset(0) info.setWaterNormal(Vec3(0, 0, 0)) resx = 31 resy = 31 p00 = Point3(-8, -8, 0) p10 = Point3( 8, -8, 0) p01 = Point3(-8, 8, 0) p11 = Point3( 8, 8, 0) fixeds = 1+2+4+8 gendiags = True bodyNode = BulletSoftBodyNode.makePatch(info, p00, p10, p01, p11, resx, resy, fixeds, gendiags) material = bodyNode.appendMaterial() material.setLinearStiffness(0.4) bodyNode.generateBendingConstraints(2, material) bodyNode.setTotalMass(50.0) bodyNode.getShape(0).setMargin(0.5) bodyNP = self.worldNP.attachNewNode(bodyNode) world.attachSoftBody(bodyNode)
First we have to configure the soft body world properties, like we did for soft body ropes too. Next we define variables for the resolution in x- and y-direction, and for the four corner points of the patch.
The variable fixeds is set to the value 1+2+4+8=15, meaning that the patch should be attached to the world on all four corners. To attach it to the first and third corner (diagonal) we would set the value to 1+8=9, and to not attach it at all we would set it to 0.
Now we can create the soft body node using the factory method
makePatch. The following
configuration differs from what we have seen for soft body ropes.
First we create an additional material attached to the soft body. Initially a soft body has already one material, but for this example we want a second one.
On the material we set the linear stiffness, and the create bending constraints for this material.
Finally we choose a value of about the grid spacing for the soft bodies margin. Other bodies colliding with the soft body could fall through in between the nodes if the value is too small, and if it is too large they will already collide with the soft body when still noticeably far away.
In order to have a visual representation of the soft body patch we need a
GeomNode. Panda3D’s Bullet
module has a helper method which will do the work for us. The following code
snippet shows how use this helper method.
from panda3d.core import GeomVertexFormat from panda3d.bulletimport BulletHelper fmt = GeomVertexFormat.getV3n3t2() geom = BulletHelper.makeGeomFromFaces(bodyNode, fmt, True) bodyNode.linkGeom(geom) visNode = GeomNode('') visNode.addGeom(geom) visNP = bodyNP.attachNewNode(visNode)
The third parameter to
is set to
True, making the
created geometry be two-sided. If set to
False we would get a
one-sided geometry, which might be enough, depending on your requirements.
So far the generated geometry has no texture and no texture coordinates. But
the texture has already a column for texcoords, so we just need to write
texcoords using a
following code shows a convenience method which will do this for us.
tex = loader.loadTexture('models/panda.jpg') visNP.setTexture(tex) BulletHelper.makeTexcoordsForPatch(geom, resx, resy)
Note: It is also possible to render soft body patches using a
SheetNode, but results are
usually better when rendering patches directly, that is using linked